----------------------------------------------------------------------
【Voltage Compatibility】
When using electrical appliances, please note that they are designed for Japanese voltage specifications (90-110V), so if you use them with a different voltage, it may cause a malfunction.
【Plug Type】
Our products use Japanese plug types (A or B type).
Please use a conversion adapter if necessary.
【Important Note on Transformers and Adapters】
A transformer adjusts voltage to match your device’s requirements.
A conversion adapter only changes the plug shape and does not adjust voltage.
Using only a conversion adapter without a transformer may result in damage to the product.
【Liability】
We are not responsible for malfunctions or damages caused by improper use, such as operating the product without a transformer.
----------------------------------------------------------------------
[Hall Joysticks and Extra Sensors] – 4x Hall Effect Stick Replacements for PS4, PS5, Xbox and most 3rd party controllers (ALPS, FU, etc.) with normal analog or hall control sticks inside. Reassemble the stick assembly with 8x extra sensors and magnets to fit your specific controller. Dedicated Vcc tester distinguishes which pins are Vcc/Gnd. (🔺Note: Make sure your controller comes with normal ✅UniA sticks.)
[HEATING PLATE INCLUDED] - The copper heating plate melts all the solder joints simultaneously with the soldering iron. Tin the wire, cut it to have a sharp tip, stick the tip into a small hole, and suck the solder into the small hole. Multi-gauge braided wire performs better than solder wick. PCB clamp helps support the PCB on your workbench. 🔺Caution: Do not place the clamp near a hot joystick or it will melt.
[Calibration Strategy] – You can adjust the center with the included tool. The outer range of these hole sticks is slightly wider than analog sticks. Although it is mentioned in the installation guide, we do not recommend calibrating the outer range with a calibration app. You can manually increase or decrease the outer range with an 8% O-ring or Teflon tape. (🔺Note: For finer control over calibration, please refer to another series of kits with MCU PCB.)
[Compatibility and Precautions] – 1. 🔺Check the images and description for compatible/incompatible sticks and controllers. 2. 🔺External magnets may interfere with hole sticks, such as the LT bumper buttons on controllers with Xbox layouts. Do not purchase if this is a concern. For kits with MCU control for Xbox, see B0CYBWQWTB. 3. 🔺Serious soldering skills and devices are required to unsolder old sticks from PCB.
[HL-FU Box Contents] – 4 x Hall Joysticks, 8 x Extra Hall Sensors & Magnets, 1 x Vcc Tester, 1 x Heating Plate, 1 x Center Adjustment Wrench, 1 x 8% O-Ring, 1 x Teflon Tape. (🔺Please make sure your soldering iron is 60 watts or higher and has a large tip. Controller, disassembly driver tool, soldering iron and other soldering tools and materials are required but not included.)
4x Hall Effect Joysticks with Adjustable Center Structure
8x Additional Hall Sensors for Different Vcc/Gnd Layout
A Dedicated Vcc Tester distinguishes Vcc/Gnd Pads on PCB
A Heating Plate helps to Desolder the old Sticks off PCB
8% O-ring and Teflon Tape for Outer Range Adjustment
Two More Choices:
1. Go to B09KVG7DGY for UniA series of Analog Stick by ALPS and FU
2. Go to B0CYBRZ2YP for hallstick series with calibration MCU PCB for fine calibration
✅Compatible Controller Example:
PS4/DS4, PS5/DS5, PS5 Edge/DSE
Some Raiiu, Razar, Scuf and most 3rd brand
Xbox One and Elite, Xbox Series S/X
(The LT bumper slightly interferes with left stick.)
🔺Incompatible Example – (Cause):
Switch Pro – (Power supply problem. Plz go to B0CYBLZPW1)
PDP Rematch 049 – (It uses a UniB stick.)
Xbox 360 – (It uses an X360 stick.)
Thunderobat G50S, Games-Sir G7 SE – (Totally different joystick used)
PS3 – (A special 4Pin stick used.)
Reminders:
1. This model is a replacement for most controllers with common type of ✅UniA control stick inside, Not for 🔺UniB or 🔺X360 type
2. We do not suggest calibrating its outer range with calibration App though we mentioned it on the user guide
3. External magnets may interfere with the hall stick, for example the LT bumper button of Xbox. Do not buy if you concern this, and take a view at B0CYBWQWTB for hallstick with MCU control
4. Teardown screwdriver tools, USB wired and wireless controllers, USB input and output charging cables Other soldering tools and materials are NOT included
